RCT TT+ Series/TTL33-A / Active three-way line array module 2×8

Beschrijving

vraag offerte voor actuele prijzen

Aktivn? Line Array, 500W+500W+250W, 2×8″+8″+3×1″, 32kg, 134dB max, 100x 15 graden

Small like a ?mini? array that sounds bigger than a ?compact?. Advanced
technologies, knowledge, experience, continuous engineering effort and
dedication were able to bring us to a unique result: the TL33-A.
Active, ultra compact, wide dispersion, line array module that sets a
new standard in touring and theatre sound reinforcement.

Digital processing
The integrated digital processor is based on a state of the art 24 bit,
floating point DSP running at 96 KHz sampling rate. The calculation
capacity largely exceed the processing needs and the DSP is never
pushed to the limit. Crossover and equalization of the 6 transducers,
limiter, system presets: high pass, air absorption and cluster size
corrections.

Digital power
The TTL33-A is powered by a 750 watt
switching power supply and 3 digital amplifiers: 500 watt mid-bass ,
500 watt midrange and 250 watt compression driver. Very high output,
extremely low distortion and natural sound . All the amplifiers and
digital processing are housed in an aluminum extrusion external to the
cabinet for best heat dissipation.

Compression drivers
A new compression driver unit has been
developed in RCF specifically for array applications. The best ratio
between the size of the diaphragm and the overall diameter and the very
small total size makes the ND1411-MT a unique driver for application in
line on straight horns. TTL33-A houses 3 of them for perfect HF
control.

Controlled mid-bass
Two light and reliable neodymium 8?,
in a band pass loading configuration, provides a tight and loud
mid-bass. Thanks to a careful acoustic design the sensitivity in the
100 Hz region is almost double than typical, same size, designs.

High output midrange
A fast and accurate horn loaded 8?
takes care of the midrange frequencies. Powerful neodymium magnet,
aluminum die cast basket, aluminum back can in direct contact to the
rear plate for best heat dissipation.

Reliable mechanics
Laser cut high quality steel bars and
precision machining for an easy to use and reliable mechanics. Thanks
to the very light weight of the cabinet building the cluster is very
simple, fast and effortless.

RCF Prediction Software
In order to assist with the set up
procedures for the TTL33-A Line Array System, RCF has developed a
complete prediction software package. The software enables a complete
two dimensional simulation of the behaviour of the TTL33-A cabinets and
also suggests the correct subwoofer combinations.
The system curvature angles and the sound projection data are computed
with maximum sound pressure levels for the given building design
originally inputted. The software will allow simulations up to a
maximum of sixteen TTL33-A mid-high cabinets.
There is also a rigging menu which provides data for weight, centre of
gravity and height of the array configuration. Rigging points and
rigging hardware configurations are also computed.

– Wide, constant directivity, coverage angle
– 6 x high power neodymium transducers

– 3 x high power class D amplifiers
– 96 kHz, 24 bit, floating point DSP

Line Array Module
ACOUSTICAL SPECIFICATIONS
Frequency Response 60-20 kHz
SPL peak 134 dB

Sensitivity (1W/1m) –
Coverage angle 100? orizz. – 15? vert. max, depending on config.
Compression Driver 3×1
Midrange 8

Woofer 2×8
Power Handling –

INPUT SECTION
Input signal- Impedance bal/unbal

Input connector xlr
Output signal connector xlr
Input sensitivity -2dBu/+4dBu
Mic. input sensitivity –

PROCESSOR SECTION
Crossover frequencies 400Hz 1800Hz
Protections thermal, hf
Sensitivity control yes

Limiter fast limiter
High pass yes, 100Hz
Controls hf correction, cluster size

AMPLIFIER

Nominal power Switching 750Watt
High frequencies D/250Watt
Mid frequencies D/500Watt
Low frequencies D/500Watt

Cooling convection/forced
Connection powercon in/out

PHYSICAL SPECIFICATIONS
Height 300mm

Width 760mm
Depth 450mm
Weight 32 Kg
Cabinet baltic birch

Hardware side fly fittings
Handles 2 on side
Pole Mount / Cap –
Colour black